Help with Assembly of Rubbermaid 35 Gallon Biofilter

[Bowhunter]

Hello,
I'm currently putting together a biofilter made from a 35 gallon
rubbermaid container. I have a question regarding the inlet, outlet,
and drain valve installation. I cut the holes in the rubbermaid
container so the pvc fit's nicely but I was wondering what to use to
glue them to the container so they will be strong and leak proof? I
know silicone is recomended to seal for leaks but is it strong enough
to hold everything in place if the container is moved around for
cleaning and such? Also...I'm putting in (4) 4" long pieces of pvc
pipe inside the container (one in each corner) to use as shelf supports
to keep the pvc pipe raised 4" off the bottom of the container. What
type of adheasive should I use for this?

Thanks so much :)
Mike

[Happy'Cam'per]

Get some O-Rings or make a rubber Gasket out a sheet of flattened rubber or
something.
--
Kind Regards
Cameron Jmaes

"Bowhunter" > wrote in message
ups.com...
> Hello,
> I'm currently putting together a biofilter made from a 35 gallon
> rubbermaid container. I have a question regarding the inlet, outlet,
> and drain valve installation. I cut the holes in the rubbermaid
> container so the pvc fit's nicely but I was wondering what to use to
> glue them to the container so they will be strong and leak proof? I
> know silicone is recomended to seal for leaks but is it strong enough
> to hold everything in place if the container is moved around for
> cleaning and such? Also...I'm putting in (4) 4" long pieces of pvc
> pipe inside the container (one in each corner) to use as shelf supports
> to keep the pvc pipe raised 4" off the bottom of the container. What
> type of adheasive should I use for this?
>
> Thanks so much :)
> Mike
>

[Gale Pearce]

If you use the regular "bulkhead" fittings, they seal themselves to the
container with a rubber gasket and won't leak and they aren't expensive
Gale :~)
> I'm currently putting together a biofilter made from a 35 gallon
> rubbermaid container. I have a question regarding the inlet, outlet,
> and drain valve installation. I cut the holes in the rubbermaid
> container so the pvc fit's nicely but I was wondering what to use to
> glue them to the container so they will be strong and leak proof? I
> know silicone is recomended to seal for leaks but is it strong enough
> to hold everything in place if the container is moved around for
> cleaning and such? Also...I'm putting in (4) 4" long pieces of pvc
> pipe inside the container (one in each corner) to use as shelf supports
> to keep the pvc pipe raised 4" off the bottom of the container. What
> type of adheasive should I use for this?
>
> Thanks so much :)
> Mike
>

[[email protected]]

Gale Pearce wrote:
> If you use the regular "bulkhead" fittings, they seal themselves to
the
> container with a rubber gasket and won't leak and they aren't
expensive
> Gale :~)
> > I'm currently putting together a biofilter made from a 35 gallon
> > rubbermaid container. I have a question regarding the inlet,
outlet,
> > and drain valve installation. I cut the holes in the rubbermaid
> > container so the pvc fit's nicely but I was wondering what to use
to
> > glue them to the container so they will be strong and leak proof?
I
> > know silicone is recomended to seal for leaks but is it strong
enough
> > to hold everything in place if the container is moved around for
> > cleaning and such? Also...I'm putting in (4) 4" long pieces of pvc
> > pipe inside the container (one in each corner) to use as shelf
supports
> > to keep the pvc pipe raised 4" off the bottom of the container.
What
> > type of adheasive should I use for this?
> >
> > Thanks so much :)
> > Mike
> >
Without bulkhead fitting you will have leaks. Bulkhead fittings can be
made up of parts in the plumbing department. Look around for gaskets or
make the out of left over EPDM rubber liner. This is the first thing I
learned from this news group. Good luck.