Adding a Skimmer

[Dan]

What is best way to add skimmer to an established pond? Either diy or store
bought. Plans? Websites? Thanks, Dan.

[RichToyBox]

The easiest is the surface skimmer AES part number S750B. It is installed
in the middle of the pond with no holes to cut in the liner. I have
installed two Pondsweep skimmers in working ponds. It is very difficult to
hold the liner up, dig the hole, install the skimmer box, and then attach
the dirty liner with the silicone sealant. For one of the ponds, I cut a
piece of plywood slightly larger than the skimmer and slid it down behind
the liner before digging. This worked for holding the liner up, but it was
difficult to get the liner pulled back far enough to get the plywood
installed.. After the hole was dug, dropped in the skimmer, pulled the
plywood, sealed the liner to skimmer, cut liner, installed weir, and face
plate. That skimmer did not have the holes drilled for the screws,
manufacturing defect I think, and I had to drill the holes underwater. Used
an old hand drill and then treated the drill with WD40 to keep it from
rusting. It helps to lower the water level as much as possible.
--
RichToyBox
http://www.geocities.com/richtoybox/pondintro.html


"Dan" > wrote in message
...
> What is best way to add skimmer to an established pond? Either diy or
store
> bought. Plans? Websites? Thanks, Dan.
>
>

[Sue Alexandre]

I agree with Rich about it being a lot of work to install one in the side of
an existing pond, BUT, I think it was worth the work! (of course that's
easy to say when it's finally installed and working properly!)
Removing the rock border from that section is not fun, and then lowering the
water, pulling the liner forward enough to work in that area yet trying NOT
to disturb the rest of the rock border by pulling the liner out TOO much,
digging is never fun, and yes, working with tools and lining up the screw
holes, etc. while you're in water/under water is challenging. But the
biggest nightmare I found was getting the hole exactly the right depth and
getting it perfectly level. And of course once you've attached the liner to
the skimmer, it's pretty hard to make any adjustments at that point, so make
sure the hole is REALLY how you want it before you attach the liner. I
could have never pulled this one off without my husband's help, but it was
SO WORTH IT - I LOVE my skimmer!
Sue
"RichToyBox" > wrote in message
news:%M1Sa.94638$N7.11976@sccrnsc03...
> The easiest is the surface skimmer AES part number S750B. It is installed
> in the middle of the pond with no holes to cut in the liner. I have
> installed two Pondsweep skimmers in working ponds. It is very difficult
to
> hold the liner up, dig the hole, install the skimmer box, and then attach
> the dirty liner with the silicone sealant. For one of the ponds, I cut a
> piece of plywood slightly larger than the skimmer and slid it down behind
> the liner before digging. This worked for holding the liner up, but it
was
> difficult to get the liner pulled back far enough to get the plywood
> installed.. After the hole was dug, dropped in the skimmer, pulled the
> plywood, sealed the liner to skimmer, cut liner, installed weir, and face
> plate. That skimmer did not have the holes drilled for the screws,
> manufacturing defect I think, and I had to drill the holes underwater.
Used
> an old hand drill and then treated the drill with WD40 to keep it from
> rusting. It helps to lower the water level as much as possible.
> --
> RichToyBox
> http://www.geocities.com/richtoybox/pondintro.html
>
>
> "Dan" > wrote in message
> ...
> > What is best way to add skimmer to an established pond? Either diy or
> store
> > bought. Plans? Websites? Thanks, Dan.
> >
> >
>
>