I got my 96 S10 apart finally that i posted about before. It was turning over funny after it flat died, so i thought i had timing chain problems. The front of the motor came apart OK until i go to the crank pulley holder. It took a LONG time with help to get it to creep off. i don't know if it...

Was helping my brother in law with his newly acquired 95 GMC suburban 4x4. No 4wd lights on the floor shift, no front axle engagement. was blowing the 4wd fuse. Did some research on the interest and found these units have some thermally engaged front actuator on the front drive axle that...

http://www.autoblog.com/2010/04/27/gm-investing-890m-in-next-gen-small-block-v8s/ bob

http://www.designnews.com/author.asp?section_id=1381&doc_id=231814&itc=dn_analysis_element& bob

http://www.impomag.com/scripts/ShowPR.asp?RID=20658 bob

http://www.youtube.com/watch?v=UqnoJyPXe4g&feature=related bob

http://www.impomag.com/news/2012/05/hail-storm-pounds-new-ford-escape-models

www.impomag.com/news/2013/05/chinas-struggling-automakers-jump-suv-boom So much for green thinking in china.... bob

http://www.pistonheads.com/news/default.asp?storyId=27436 whos knows whats up GM's sleve. whats next? bring back the big block? Maybe the CHevette? ;) bob

http://eetweb.com/applications/EV_fires_12111/index.html bob

http://en.wikipedia.org/wiki/Chicken_tax bob

Got a chance to get a 1988 cube van cheap. I have not seen it yet. It has a 350 diesel. tranny won't go into forward. My questions a whose diesel would have been in a 88 cube van? Was it a good engine and what kind of problems did they have? Which automatic trannie would have been mated to it?

I am trying to help my bro fix a 87 fiero GT. The shift cables are shot. There are some on ebay now. My question is, are the GT shift cables the same as the straight 2m6 cables? Are the trannies different between the GT and the regular 6 cylinder model? Bob ----== Posted via Newsfeeds.Com -...

I have a 96 S10 which i have been regularly trying to fix.. ;) I bought the two book GM factory shop manuals for the truck. They are good, BUT they have very little electrical schematics on the trucks electrical system. Was there a separate factory manual for electrical schematics? On the after...

I have had my 1996 S10 for a few years now and ever time it gets cold in the midwest i have a problem with the IAT sensor. Its fine when its warm, only when its below 40 degrees. (OBDII codes pop) Sensor has been changed. Head was off and harnesses re grounded. I am assuming its a bad solder joint...

http://www.ts-mag.com/t_stx.cfm?action=newspick&id=2094 bob

new for gm http://autoelectronics.com/news/hella-led-headlamps-cadillac-0131/ BOB

I bought this 97 Taurus in good shape with a blown head gasket. put another 3.0L Vulcan in it. It starts and runs fine, BUT it runs over 3/4 the way + to the end line on the heat gauge. I flushed the transplant motor before installation. Put a new water pump on it. New thermostat with giggle...

There seems to be a number of sellers (some on ebay) selling imported replacement radiators for much cheaper prices. Anybody got a real world opinion's on these? good? bad? issues?

http://www.electronicproducts.com/Electromechanical_Components/Motors_and_Controllers/Company_unveils_next-generation_flying_car.aspx bob