I have a 1998 corolla and it is overcooling. I think the engine temperature sensor is bad. However, it is located against the engine block by coolant inlet ports and hard to get at with conventional tools? Anyone know how to do it?

I have a 1998 corolla and it is overcooling. I think the engine temperature sensor is bad. However, it is located against the engine block by coolant inlet ports and hard to get at with conventional tools? Anyone know how to do it?

I have a 1998 toyota corolla and it is overcooling. I think the engine temperature sensor is bad. However, it is located against the engine block by coolant inlet ports and hard to get at with conventional tools? Anyone know how to do it?

Ok, so disassembling everything for my head gasket replacement WAS going well, in fact all too well, so fate had to do something drastic. Got everything off except the intake manifold and cam sprocket. I go to slack the timing belt, and the bolt head on the tensioner is COMPLETELY messed up. It...

Removed throttle body for cleaning.............74973 KM I first of all removed air filter cover..........disconnected plug attached to rubber accordion hose...........to disconnect plug, slide red lock slider on top of disconnect plug backwards and pull plug out...............PS when you...

How to remove and replace a snap ring in a FWD car. I hit a curb with my car and broke in half the right half-axle, broke a big chunk out of the RF rim and a piece the size of a tea-cup saucer from the tire too, cracked my lower suspension arm, and severed the right ball joint (2000 Toyota Solara,...

I've convened this multi-disciplinary forum, becuase this is a multi-faceted problem. How to remove CD's from broken auto CD changer? I have a 2000 Toyota Solara with a factory AM-FM-CD changer, all in the dash, not the trunk. It worked fine until about 2014, with 6 cd's in it, a full load,...

I'm looking for help in removing the center console on an alero - I can't seem to get past removing the gear shift lever. - I need to ge to the fan and air conditioning controls. Any simple hints?

Anyone know how to remove the door panel on a 1997 Buick Skylark? I need to replace the power window motor. Can't get the door panel off, there's some tricks to it but I dont want to break clips or something. Thanks Larry

I can't get this horn button off -- tried prying, but afraid to break it off. Not sure if it turns, pries, or what. Shop manual just says 'remove' (big help). It's a 1990 B2600i. No air bag, just a 4" diam. leathette button. I want to pull the steering wheel to replace an intermittent...

If a system has received refrigerant + oil charges over time and will no longer take a full refrigerant charge because of the accumulation of oil in the system, how to you remove the oil? Will a vacuum pump remove any of this as it takes the gas out of the lines? -Inet

I took the oil pan off my '84 VW Rabbit (diesel). Unfortunately, most of the old (paper) gasket stuck to the bottom of the engine. How do I remove it? It's practically superglued on. I've tried gasket remover, a scraper, a razor blade, a wire wheel on a Dremel... the stuff clings to my engine block...

I'm planning to do a complete 4 wheel brake job on my '95 Acura Integra this weekend. the front pad removal is very straightforward, but I simply cannot figure how to remove the rear or more specifically- how to back-off the caliper so I can put new pads on them. Any special technique or tool...

Hi I have a 1984 VW Rabbit GTI I need to replace the control arm. Figured I would replace both sides as the bushings are not in that great shape. I found a great package, control arm both bushings, ball joint and all the hardware for only $44 per side. So my question is, should the front...

Please tell me how to remove the fuseblock on a 1994 Corsica. Thank you.

Any help would be appreciated on information of how to remove the valves on the engine. I am trying to replace the valve stem seals. It's a 12-valve Ford pushrod V6 from a 1998 Taurus. Thanks in advance, Tim

I have an 03 Sierra and I can't find how the driver side wiper arm comes off the threaded bolt, Ive removed the nut and tried to pull it , pry it , WD/40 it, used a batterie cable puller, nothing is working, I can't see any clips holding it on the bolt, nothing. can anyone help? Thanks Buddy

I need to replace the wipers on my 94 geo metro, but I can't figure out how to get the old ones off. There is some kind of bold, but no screws or anything that comes apart or off in any way. Does anyone have any idea?

Well, for those of you who have kindly responded to my previous questions, this is becoming a bit of a saga. We obtained a new timing tensioner and mounting bolt, and the motor is put back together, so I decided to install the timing belt before doing the valve lash. Got the belt...

Specs: 1998 ford explorer, 4.0, SOHC, and a really frustrated driver! Is there any way to get this plug wire off without ripping it out. I can touch it, but do not have the leverage needed to remove the stuck boot. It doesn't appear that there is anything capable of being removed that will allow...