How to start hard to start powerheads/pumps....
 

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Use a powerful permanent magnet (like 1 half of a large mag-float
magnet algae scraper) by pressing it against the back of the
powerhead or pump while power is applied. This should start any
powerhead or pump but you might have to experiment a tad as to where
to apply the magnet to the powerhead/pump (the experimenting is a one
time only event requirement). This method should easily start any
difficult to start powerheads/pumps, and if you use a mag-float to do
it you can easily start the powerhead/pump underwater. I just thought
I would share another one of my discoveries. Good luck all and
later!

- --
You can find my public key at https://keyserver1.pgp.com

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.2 (MingW32) - WinPT 0.7.96rc1

iQD1AwUBQ4zQIq2WfcjE5myzAQLFiQb/ciS7yGgrQ6NsrhWXRa8fSl5P3dBxjFGc
6tz57wPjAdKKnB8VSYcnDz+G3eTrvad1vE1j6EihJ2WfKk5Ne/tSV/j9K5kzIFaO
Y4sIEyPHeR3tqXVbsXdlsJ6Y6C8rYPDfYW+V1N7lFknPq4zfx0 Ms9ae0FwgrUpso
QZ6UkluLj8sIoGcVyaLzXY0bT7hZthvn1jA3GkN4sE2EGBaAR5 xsnZ6Mk6ybKh45
MZ817/sWu6q8RfJl+A8Ytc/95l2bcIUF/24hm7Y9CyWTl/7eDEz6lBLreFW+i03X
N3Frfz/qOt4=
=Z+Ue
-----END PGP SIGNATURE-----

How to start hard to start powerheads/pumps....
 

Just smack it!!!


"Daniel Morrow" wrote in message
...
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Use a powerful permanent magnet (like 1 half of a large mag-float
magnet algae scraper) by pressing it against the back of the
powerhead or pump while power is applied. This should start any
powerhead or pump but you might have to experiment a tad as to where
to apply the magnet to the powerhead/pump (the experimenting is a one
time only event requirement). This method should easily start any
difficult to start powerheads/pumps, and if you use a mag-float to do
it you can easily start the powerhead/pump underwater. I just thought
I would share another one of my discoveries. Good luck all and
later!

- --
You can find my public key at https://keyserver1.pgp.com

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.2 (MingW32) - WinPT 0.7.96rc1

iQD1AwUBQ4zQIq2WfcjE5myzAQLFiQb/ciS7yGgrQ6NsrhWXRa8fSl5P3dBxjFGc
6tz57wPjAdKKnB8VSYcnDz+G3eTrvad1vE1j6EihJ2WfKk5Ne/tSV/j9K5kzIFaO
Y4sIEyPHeR3tqXVbsXdlsJ6Y6C8rYPDfYW+V1N7lFknPq4zfx0 Ms9ae0FwgrUpso
QZ6UkluLj8sIoGcVyaLzXY0bT7hZthvn1jA3GkN4sE2EGBaAR5 xsnZ6Mk6ybKh45
MZ817/sWu6q8RfJl+A8Ytc/95l2bcIUF/24hm7Y9CyWTl/7eDEz6lBLreFW+i03X
N3Frfz/qOt4=
=Z+Ue
-----END PGP SIGNATURE-----

How to start hard to start powerheads/pumps....
 

"Daniel Morrow" wrote in message
...
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Use a powerful permanent magnet (like 1 half of a large mag-float
magnet algae scraper) by pressing it against the back of the
powerhead or pump while power is applied. This should start any
powerhead or pump but you might have to experiment a tad as to where
to apply the magnet to the powerhead/pump (the experimenting is a one
time only event requirement). This method should easily start any
difficult to start powerheads/pumps, and if you use a mag-float to do
it you can easily start the powerhead/pump underwater. I just thought
I would share another one of my discoveries. Good luck all and
later!

- --


I'll have to remember that, thanks.
--
www.NetMax.tk