Built-in Overflow Problem
 

Hey guys,

I have a new 125-gallon glass tank with a built-in overflow. The problem
is that, even though the tank is level, the water level stays below the
plastic rim of the tank. Is there anything short of modifying the
built-in overflow that I can do to increase the water level in the tank?

I tried adjusting the level of the water inside the overflow and that
has no effect, and adding more water just raises the water level in the
sump.

Thanks.

Built-in Overflow Problem
 

"Jerry Baker" wrote in message news:upcRg.706$Vk4.257@trnddc01...
I have a new 125-gallon glass tank with a built-in overflow. The problem
is that, even though the tank is level, the water level stays below the
plastic rim of the tank. Is there anything short of modifying the
built-in overflow that I can do to increase the water level in the tank?

I tried adjusting the level of the water inside the overflow and that
has no effect, and adding more water just raises the water level in the
sump.

What pump do you use? Does it have enough flow ?
Usually, the stronger pump = higher water level in the tank.

Try to find out for how much wate flow is your overflow rated
and pick a pump which delivers flow near this maximum at
a given hight. (flow decreases with the pumping hight)

Built-in Overflow Problem
 

Yep, definitely don't have enough water flow for a reef
tank, if the water level is that low.

Wayne Sallee
Wayne's Pets



Pszemol wrote on 9/23/2006 11:34 AM:
"Jerry Baker" wrote in message
news:upcRg.706$Vk4.257@trnddc01...
I have a new 125-gallon glass tank with a built-in overflow. The
problem is that, even though the tank is level, the water level stays
below the plastic rim of the tank. Is there anything short of
modifying the built-in overflow that I can do to increase the water
level in the tank?

I tried adjusting the level of the water inside the overflow and that
has no effect, and adding more water just raises the water level in
the sump.

What pump do you use? Does it have enough flow ?
Usually, the stronger pump = higher water level in the tank.

Try to find out for how much wate flow is your overflow rated
and pick a pump which delivers flow near this maximum at
a given hight. (flow decreases with the pumping hight)

Built-in Overflow Problem
 

Wayne Sallee wrote:
Yep, definitely don't have enough water flow for a reef tank, if the
water level is that low.

Ya, the tank is a freshwater tank but trying to ask anyone in freshwater
about overflows and sumps isn't likely to get much response. The flow is
about at the limit of what the 1" drain can handle.

Built-in Overflow Problem
 

"Jerry Baker" wrote in message news:VjpRg.1946$Vk4.918@trnddc01...
Wayne Sallee wrote:
Yep, definitely don't have enough water flow for a reef tank, if the
water level is that low.

Ya, the tank is a freshwater tank but trying to ask anyone in freshwater
about overflows and sumps isn't likely to get much response. The flow is
about at the limit of what the 1" drain can handle.

Is this tank purchased with overflow or you built it yourself?
Usually, tanks available at stores (Allglass, Oceanic) have
overflows properly designed to rise water above frame level.

If this is do-it-yourself overflow, than I would suggest modyfying
the hight of the comb - limit the flow through the overflow
on the side where the water leaves the tank. Plug couple of
teeth/cuts in the comb to limit speed of water flowing on the
other side... This will rise the water level. Do not overdo it... ;)

p.s. what pump do you use ? how much gallons/hour or litter/hour ?

Built-in Overflow Problem
 

Pszemol wrote:
Is this tank purchased with overflow or you built it yourself?
Usually, tanks available at stores (Allglass, Oceanic) have
overflows properly designed to rise water above frame level.

This tank was purchased with the overflow built-in.

p.s. what pump do you use ? how much gallons/hour or litter/hour ?

The pump is a cheapo Rio 1700 (650gph).

The overflow has 12 1/4" teeth. I have to plug up 8 of them before the
water level gets above the plastic rim. My only task now is to plug them
up in a non-permanent way that isn't visible while viewing the tank.

Built-in Overflow Problem
 

"Jerry Baker" wrote in message news:OaBRg.1460$fl2.989@trnddc02...
Pszemol wrote:
Is this tank purchased with overflow or you built it yourself?
Usually, tanks available at stores (Allglass, Oceanic) have
overflows properly designed to rise water above frame level.

This tank was purchased with the overflow built-in.

Who is the manufacturer ? Is this Allglass tank ?

This is interesting that such a big tank has only one 1" overflow...

I have a tank half the size (3 foot, 58gallons) with such a 1" overflow.
I use one QuietOne 3000 pump which is rated at about 750gph.

Your tank should have 2 or 3 such overflows or bigger hole.
Sounds like a home-made overflow in this tank...

p.s. what pump do you use ? how much gallons/hour or litter/hour ?

The pump is a cheapo Rio 1700 (650gph).

The overflow has 12 1/4" teeth. I have to plug up 8 of them before the
water level gets above the plastic rim. My only task now is to plug them
up in a non-permanent way that isn't visible while viewing the tank.

Or design a new comb from a piece of black plastic and
cover the old one slightly higher.

Built-in Overflow Problem
 

Pszemol wrote:
Who is the manufacturer ? Is this Allglass tank ?

Lee-Mar. They are a local California company.

Or design a new comb from a piece of black plastic and
cover the old one slightly higher.

The plastic already goes to the top of the tank. I can't go over it,
only plug teeth up.

Thanks.

Built-in Overflow Problem
 

"Jerry Baker" wrote in message news:JMCRg.1466$Wi1.382@trnddc06...
Pszemol wrote:
Who is the manufacturer ? Is this Allglass tank ?

Lee-Mar. They are a local California company.

Shame...

Or design a new comb from a piece of black plastic and
cover the old one slightly higher.

The plastic already goes to the top of the tank. I can't go over it,
only plug teeth up.

How long are the vertical cuts between teeth ?
Maybe you will be able to cover bottom part of comb on
its whole lenght with a stripe of black plastic - this way
it will look better than pluging each tooth separatelly.
Each cut will be shortened this way and water level will
be lifted up.

Built-in Overflow Problem
 

Pszemol wrote:
How long are the vertical cuts between teeth ?
Maybe you will be able to cover bottom part of comb on
its whole lenght with a stripe of black plastic - this way
it will look better than pluging each tooth separatelly.
Each cut will be shortened this way and water level will
be lifted up.

I was going to block off two sides and leave the front (each has 4
teeth) using a piece of black plastic. What I can't figure out how to do
is stick the plastic to the overflow without using glue or silicone
since I want it to be easily removable.