![]() |
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
![]()
I just picked up a pair of Danner Mag-7 water pumps. I'm planning
on using them in parallel redundancy on a 180G tank I'm setting up. To test them I placed them in a 5 gallon bucket filled with water and turned them on overnight. The next morning, to my horror, when I placed my hand in the bucket to feel the water flow I just about got burned. The water was VERY hot, well over 100 degrees. Does this sound right? I know they're supposed to dissipate SOME heat into the water when used submerged. And I also know that the problem won't be so bad in a 180G tank compared to a 5G bucket. BUT THAT WATER WAS HOT! I'm starting to worry about poached fish. ADVthaAnksNCE |
#2
|
|||
|
|||
![]()
Joel M. Baldwin wrote:
To test them I placed them in a 5 gallon bucket filled with water and turned them on overnight. The next morning, to my horror, when I placed my hand in the bucket to feel the water flow I just about got burned. The water was VERY hot, well over 100 degrees. Well, look at it this way. On the nameplate it should say how many watts of power they use. Think about heaters that use that many watts. Surely that's too much to have on ALL the time in a five gallon tank. But is thatt number a fair amount below the amount of thermostat-controlled heating you have in the tank? If so, then I'd not worry, since the heat effect is going to be like that of x-watt heaters (where x is what the two pumps use) turned on all the time. I expect we're talking 60 watts here, and I expect that a 60-watt, alone in that tank, would never turn off on its own. So really, don't sweat it. Your heaters might turn on a little less. That's it :-) --jjoe |
#3
|
|||
|
|||
![]()
Jesse Joe wrote in news:d4rbo9$mjm$1@news-
int2.gatech.edu: Joel M. Baldwin wrote: To test them I placed them in a 5 gallon bucket filled with water and turned them on overnight. The next morning, to my horror, when I placed my hand in the bucket to feel the water flow I just about got burned. The water was VERY hot, well over 100 degrees. Well, look at it this way. On the nameplate it should say how many watts of power they use. Think about heaters that use that many watts. Surely that's too much to have on ALL the time in a five gallon tank. But is thatt number a fair amount below the amount of thermostat-controlled heating you have in the tank? If so, then I'd not worry, since the heat effect is going to be like that of x-watt heaters (where x is what the two pumps use) turned on all the time. I expect we're talking 60 watts here, and I expect that a 60-watt, alone in that tank, would never turn off on its own. So really, don't sweat it. Your heaters might turn on a little less. That's it :-) --jjoe Logical and reassuring, however I would have expected that a large portion of that 60watts to be expressed as mechanical energy in the water movment, not as thermal energy into the water. Your explaination of needing less heater wattage as a result is useful during the winter when the house is cold and the water needs to be heated, but during the summer my house will be quite warm and a heater won't be on very often. I may end up with a tank that is too hot. I'm starting to think I should mount them inline rather than submerged. And make sure that the sump area is WELL ventilated. |
#4
|
|||
|
|||
![]()
"Joel M. Baldwin" wrote:
Logical and reassuring, however I would have expected that a large portion of that 60watts to be expressed as mechanical energy in the water movment, not as thermal energy into the water. Most of the power *does* initially get used to move the water. However, the same effects that result in the water movement being damped in the aquarium (friction, etc.) ultimately result in most of the energy being converted to randomized heat. |
#5
|
|||
|
|||
![]() I have a few Danner mag drives that are usableas external or submersible to ppower various filters etc on some tanks I keep outside. In the summer time I run them as externals so they do not get too much heat built up in the tanks, in the winter they run as submersibles and helps keep the water warmer and heaters off longer. ============================================== Put some color in your cheeks...garden naked! |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Alternative Heat For Tank (experiment) | pausto | Tech | 6 | January 17th 05 11:54 AM |
Use indoor heat on Pond | MC | General | 14 | April 7th 04 03:06 AM |
Heat from the AH Supply Bright Kit #30552 ?? | Shawn P. Good | General | 2 | February 22nd 04 05:32 PM |
How much more heat if you go from 175W to 250W | ljtellef | Reefs | 6 | November 1st 03 05:10 PM |
pump heat transfer; recommendations ? | Kevin M. Smith | Reefs | 2 | October 11th 03 11:43 PM |