If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Problem with the air flow sensor
I've finally figured out what the problem is with my newly bought '92
BMW 535. The air flow sensor is messed up. I removed it and measured the resistance while opening the vane and it wasn't linear at all. Closed it was 680 ohm, opened a little about 1100, almost fully open 110, and completely open 420 ohm. I cleaned the circuit board and readjusted the pick up to get 1100 ohm completely closed and then the drop was pretty much linear, except for a few spikes up to 900 ohm, down to 100 ohm at about 70% open. More than 70% the resistance would increase and at about 90% it would go off the circuit board and into infinity. Figured if I drive gently I'll be okay until I get a new air flow sensor. I thought it would be best to reset the ECM too, so I removed the minus cable off the battery and waited a while. However, now the car runs *really* rich and the idle will oscillate until it stalls. So far I've only driven for 10-15 minutes, but how long does it take before the ECM relearns what it needs to know? Also, what should the resistance be for the air flow sensor, and is it possible to buy a new circuit board instead of the whole "box"? Ulf |
Ads |
#2
|
|||
|
|||
Did you try cleaning the MAF first? You may not really need a new one.
|
#3
|
|||
|
|||
|
#4
|
|||
|
|||
In article >,
Ulf > wrote: > I've finally figured out what the problem is with my newly bought '92 > BMW 535. The air flow sensor is messed up. I removed it and measured the > resistance while opening the vane and it wasn't linear at all. Closed it > was 680 ohm, opened a little about 1100, almost fully open 110, and > completely open 420 ohm. I cleaned the circuit board and readjusted the > pick up to get 1100 ohm completely closed and then the drop was pretty > much linear, except for a few spikes up to 900 ohm, down to 100 ohm at > about 70% open. More than 70% the resistance would increase and at about > 90% it would go off the circuit board and into infinity. The correct way is to look at the output voltage with the ignition on with a scope. You should start out with a supply voltage of 4.3 volts. With the flap at rest, the output should be 3.7. slowly move the flap and look for irregularities. Fully open should be 1.6. -- *Half the people in the world are below average. Dave Plowman London SW To e-mail, change noise into sound. |
#5
|
|||
|
|||
Dave Plowman (News) wrote:
> In article >, > Ulf > wrote: > >>I've finally figured out what the problem is with my newly bought '92 >>BMW 535. The air flow sensor is messed up. I removed it and measured the >>resistance while opening the vane and it wasn't linear at all. Closed it >>was 680 ohm, opened a little about 1100, almost fully open 110, and >>completely open 420 ohm. I cleaned the circuit board and readjusted the >>pick up to get 1100 ohm completely closed and then the drop was pretty >>much linear, except for a few spikes up to 900 ohm, down to 100 ohm at >>about 70% open. More than 70% the resistance would increase and at about >>90% it would go off the circuit board and into infinity. > > > The correct way is to look at the output voltage with the ignition on with > a scope. > > You should start out with a supply voltage of 4.3 volts. > > With the flap at rest, the output should be 3.7. slowly move the flap and > look for irregularities. Fully open should be 1.6. Thanks for the info. I'll see what my old air flow sensor has for voltages after I try to repair it. Found a few ideas on this page: http://member.rivernet.com.au/btaylo...rCalibrat.html Either way, it runs great now. Next step are the thrust arm bushings. http://www.bmwe34.net/e34main/mainte.../upper_arm.htm I know the discs are slightly warped, but the worn bushings are probably amplifying the vibrations in the steering wheel, and they're cheaper to replace. :-) Ulf |
#6
|
|||
|
|||
In article >,
Ulf > wrote: > > The correct way is to look at the output voltage with the ignition on > > with a scope. > > > > You should start out with a supply voltage of 4.3 volts. > > > > With the flap at rest, the output should be 3.7. slowly move the flap > > and look for irregularities. Fully open should be 1.6. > Thanks for the info. I'll see what my old air flow sensor has for > voltages after I try to repair it. I forgot to say this was from a generic Bosch repair manual - not from one specific to your car. -- *TEAMWORK...means never having to take all the blame yourself * Dave Plowman London SW To e-mail, change noise into sound. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
rec.autos.makers.chrysler FAQ, Part 1/6 | Dr. David Zatz | Chrysler | 5 | May 8th 05 05:29 AM |
rec.autos.makers.chrysler FAQ, Part 4/6 | Dr. David Zatz | Chrysler | 0 | April 22nd 05 05:32 AM |
rec.autos.makers.chrysler FAQ, Part 1/6 | Dr. David Zatz | Chrysler | 10 | January 2nd 05 05:15 AM |
rec.autos.makers.chrysler FAQ, Part 1/6 | Dr. David Zatz | Chrysler | 10 | November 16th 04 05:28 AM |
Climatronic Diagnostic Controls | Luís Lourenço | Audi | 1 | November 12th 04 08:22 AM |