If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#11
|
|||
|
|||
'89 CRX won't start - frustration
"jim beam" > wrote
> when testing spark leads with an old plug, open the gap right up - > sparking distance is different at atmospheric pressure vs. cylinder > compression pressure. This is pointless if you simply want to check for spark. The correct way to check for a faulty plug or coil output is to check the spark jump at the distributor. This is easily done alone. |
Ads |
#12
|
|||
|
|||
'89 CRX won't start - frustration
ThomasE wrote:
> Thank you for your replies > ? I know how to spray started fluid on a carburetor car but how can I > spray starter fluid in a fuel injection car, there does not seem to be an > access point to the air intake. > > Thanks for the link to the main relay description. It seems to me that the > main relay should be ok since I have fuel pressure, so the relay and > computer are feeding current to the fuel pump correctly (I can also hear > the fuel pump running for 2 seconds when the ignition is turned on). As > far as the power to the injectors goes I assume that if the main relay > were not supplying voltage to the injectors that I would get a code from > the computer (or will I not? ), but as I said I get no computer codes. Injector operation (that they ARE operating, that is, not necessarily that they're operating PROPERLY) is easily checked: crank the car over a bit, then immediately take a plug out and see if it's wet with gas. Have you tested the compression? --- avast! Antivirus: Outbound message clean. Virus Database (VPS): 0612-4, 03/25/2006 Tested on: 3/26/2006 9:24:22 AM avast! - copyright (c) 1988-2005 ALWIL Software. http://www.avast.com |
#13
|
|||
|
|||
'89 CRX won't start - frustration
Burt wrote:
> "jim beam" > wrote > > >>despite your main relay test, intermittent no-start usually /is/ >>main relay in my experience, especially for a civic/crx this age. >>usually accompanied by a code 16 though. > > > Like Graham W said, if there's fuel pressure the main relay is fine. > That is how the circuit works. > er, ok, so when your *intermittent* fault happens to be /not/ evident when you test, and faulty when you're trying to start, then what? fact: for this age civic/crx, you're well inside 3 sigma on relay faults. |
#14
|
|||
|
|||
'89 CRX won't start - frustration
Burt wrote:
> "jim beam" > wrote > > >>when testing spark leads with an old plug, open the gap right up - >>sparking distance is different at atmospheric pressure vs. cylinder >>compression pressure. > > > This is pointless if you simply want to check for spark. no it's not. because it's harder to spark a small gap than a larger one at atmosphere, you may not see a spark, even if the system is ok. > > The correct way to check for a faulty plug or coil output is to > check the spark jump at the distributor. This is easily done alone. not on a honda and trying to use a normal plug lead it's not. the connector is too recessed and the hole too small for the lead to fit. if you're /not/ using a plug lead, there's too much chance of leakage to spark reliably, particularly if you're trying to spark on a plug without the gap opened to work at atmospheric pressure. besides, if the distributor cap or distributor arm are faulty you need to test "downstream" of those components. |
#15
|
|||
|
|||
'89 CRX won't start - frustration
I have not tested for compression but I have no reason to believe that
anything is wrong with it. The car was working fine then I left it in the garage for 2 weeks and now it does not start. I know that the cranckshaft is turning properly, no broken timing belts etc. |
#16
|
|||
|
|||
'89 CRX won't start - frustration
Just to eliminate some things:
Have you tried the cure listed at http://www.tegger.com/hondafaq/start...s.html#flooded for flooded cylinders? This may happen with leaky injectors after the car sits awhile. I see your comments on your main relay check, but I am still concerned about whether the pump continues running. You say fuel pressure is there, but is it continuously there? From looking at tegger.com's description, I am still suspicious. See for example the more detailed discussion at http://www.tegger.com/hondafaq/mainr...mainrelay.html (Sorry, it's hard to tell exactly what's going on. It's the price of diagnosing via posts.) If the main relay has never been replaced or re-soldered, I'd sure be inclined to take it out and re-solder. The main relay is such a common problem on older Hondas. My 91 Civic's died in 1999, after about a year of intermittent no start conditions. As for codes, the computer and code setoff system are not very sophisticated on these older Hondas. I do not recall seeing codes set in the past when people have reported a no-start problem and re-soldering or replacement of the relay fixed it. How old are your ignition wires? Are they OEM? "ThomasE" > wrote >I have not tested for compression but I have no reason to >believe that > anything is wrong with it. The car was working fine then I > left it in the > garage for 2 weeks and now it does not start. > I know that the cranckshaft is turning properly, no broken > timing belts > etc. > |
#17
|
|||
|
|||
'89 CRX won't start - frustration
ThomasE wrote:
> I have not tested for compression but I have no reason to believe that > anything is wrong with it. The car was working fine then I left it in the > garage for 2 weeks and now it does not start. > I know that the cranckshaft is turning properly, no broken timing belts Yes, it's unlikely you'd lose compression on all four cylinders after sitting for just two weeks - okay VERY VERY unlikely - but it's worth checking just to cover all the bases. Low compression combined with other issues could be the root of your problem. --- avast! Antivirus: Outbound message clean. Virus Database (VPS): 0612-4, 03/25/2006 Tested on: 3/26/2006 11:11:59 AM avast! - copyright (c) 1988-2005 ALWIL Software. http://www.avast.com |
#18
|
|||
|
|||
'89 CRX won't start - frustration
Fuel pressure is there. After cranking for 20 seconds, no start and fuel
pressure still around 37psi. Also after cranking and turning the key off the system seems to hold pressure, at least for 5 minutes which perhaps indicates that injectors are not leaking (am I correct to assume so?) I also took out all 4 spark plugs and cleaned them but again no firing. The spark plugs were not completely dry when I took them out but I cannot evaluate if they were too wet. I assume that after cranking for a while it would be normal for them to be somewhat wet. I'll repeat taking out the plugs and inspecting them after cranking. I'll take out the main relay and resolder it tomorrow. I'm pretty sure the pump is ok but the relay could still not be feeding voltage to the injectors properly. Although one would think that that would result in a code there is no description of the logic that the computer uses to detect an injector problem condition... |
#19
|
|||
|
|||
'89 CRX won't start - frustration
Oh the ignition wires are pretty old and they are OEM. But could all 4
wires fail all of a sudden? I'll do some more methodical testing tomorrow... |
#20
|
|||
|
|||
'89 CRX won't start - frustration
"jim beam" > wrote
> no it's not. because it's harder to spark a small gap than a larger one > at atmosphere, you may not see a spark, even if the system is ok. Anyone with near 20/20 vision can see the spark on a plug. To bend the plug only ask for trouble. Each time it bends it has the potential to break. If you don't see the spark then there is an ignition problem. Better to not bend it. > not on a honda and trying to use a normal plug lead it's not. the > connector is too recessed and the hole too small for the lead to fit. > if you're /not/ using a plug lead, there's too much chance of leakage to > spark reliably, particularly if you're trying to spark on a plug without > the gap opened to work at atmospheric pressure. Actually, trick requires just a paper clip... no plugs needed. If you have difficulty checking for a dead plug at the distributor like the way I do it on Accords, Civic then the timing light is your best friend. For other's reference: Hook timing light to plug wire, no light = dead plug. One dead plug = flooding. Flooding = no start. > besides, if the distributor cap or distributor arm are faulty > you need to test "downstream" of those components. You need to test both "downstream" and "upstream." |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Is it a sign that it is a battery problem if it is difficult to start a car in a hot or humid day? | Honda2nd | Honda | 6 | November 17th 05 08:22 PM |
83 VW Rabbit Hard to start and progressively looses power and dies. Cold start? Fuel pressure? Electrical? URGENT. Please respond! | Mark Amero | BMW | 11 | August 4th 05 10:39 PM |
LHS Won’t start in Cold weather and Check engine light on. | jgcurt | Chrysler | 22 | January 10th 05 07:57 PM |
periodically won't start | missjoan | Saturn | 4 | November 1st 04 05:48 PM |