If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#11
|
|||
|
|||
WARNING, ON TOPIC POST!
When I try this using the plug, I always end up with an arm full of oil, and
usually end up dropping the plug. At least the oil filer method limits the amount of drained oil. "pws" > wrote in message news > Zog The Undeniable wrote: > > > Or just let a bit run out of the sump plug. The washer will be fine if > > reused just this once. > > More than just this once. > I re-used the washer on my last car at least 10 times and it never > leaked a drop from drain hole. I know the previous owner of a 1991 model > who went over 10 years using the same washer without leaking. > > The original washer on my parent's Camry is leaking a tiny amount of oil > after 13 years and 145K miles, so I will probably make sure I replace > mine at least once every 30 oil changes or so. > > Pat |
Ads |
#12
|
|||
|
|||
WARNING, ON TOPIC POST!
Chuck wrote:
> When I try this using the plug, I always end up with an arm full of oil, and > usually end up dropping the plug. I agree, it also keeps you from getting underneath the car, a place I don't like to be no matter how well supported the car is. I have spent a lot of hours under there and it just gets less comfortable as time rolls on. Oh, the joy of a real lift! Every home garage should come standard with one. ;-) I was just pointing out that when I started reading about miatas, there seemed to be a near-fanatical response to any oil change question that said your miata would blow up, vaporize, go into a time warp or whatever if a new crush ring was not used. After talking to a trusted friend who assured me that this was pure BS and that he had used the same drain plug ring through at least 20 oil changes, I gave it a try. Like it was pointed out by another poster, there is no real reason not to use a new one, many vendors tape one onto the filter box, but there really isn't a reason to use it either that I can see. I have about 30 of them in my toolbox if anyone thinks that I am wrong and needs one for free. I think that I have a lifetime supply. :-) Pat |
#13
|
|||
|
|||
WARNING, ON TOPIC POST!
> Like it was pointed out by another poster, there is no real reason not
> to use a new one, many vendors tape one onto the filter box, but there > really isn't a reason to use it either that I can see. > I have about 30 of them in my toolbox if anyone thinks that I am wrong > and needs one for free. I think that I have a lifetime supply. :-) > > Pat I agree. The washer is made out of aluminum. It can be re-used until it is either damaged some how (surface is not flat) or is squeezed so thin it no longer compresses, which means you're tightening it too much. A new washer is not necessarily better than the old one, if it is the wrong size or has a damaged surface. You can clean up the surface with some fine wet sandpaper if you happen to damage it some how or buy a new one with a scratch across the surface... |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Get paid to post in forums.. | [email protected] | Technology | 9 | August 20th 06 04:10 AM |
A Post, Front Xmember and Step sill picture needed! New crossmember2.JPG (01/01) | Grahame Rumballe[_1_] | VW air cooled | 0 | August 1st 06 04:08 AM |
A Post picture needed! | Mac | VW air cooled | 1 | July 28th 06 01:51 AM |
ABS Warning Light | TCCdestroy | Audi | 2 | July 7th 05 07:20 PM |
78 Audi 5000 Cruise Control Warning Light Problem | TurboBanana | Audi | 2 | May 25th 04 03:40 PM |