If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
rear wheel drum on 1999 voyager
I am planning to inspect my rear brakes this weekend, as I suspect there
might be a problem back there. I tried briefly to get one rear drum off a few months ago when I replaced the front brakes, but it was being held in place somehow and I didn't feel like messing with it at the time. Before I get into it this Saturday, do you suppose it's just the shoes getting caught on a ridge in the drum, or is there some kind of sneaky pin or clip that holds this drum in place? |
Ads |
#2
|
|||
|
|||
rear wheel drum on 1999 voyager
Robbie and Laura Reynolds Wrote: > do you suppose it's just the shoes > getting caught on a ridge in the drum, or is there some kind of sneaky > pin or clip that holds this drum in place? More than likely just the shoes caught. You can use a hammer with a medium amount of effort, and strike the sides of the drum to free them up. Sometimes it only takes a few times, sometimes alot. -- wrightz28 ------------------------------------------------------------------------ wrightz28's Profile: http://www.automotiveforums.com/vbul...?userid=309970 View this thread: http://www.automotiveforums.com/vbul...d.php?t=622212 http://www.automotiveforums.com |
#3
|
|||
|
|||
rear wheel drum on 1999 voyager
I don't suppose you had the parking brake on by any chance???
If I recall correctly on my 1994 with rear drums, the style is different than others I encountered. That is, on some vehicles I have owned, the drum was NOT a part of the bearing assembly, so when the wheel was removed, you could simply slide the drum off to gain access to the brake mechanism. This was NOT the case on my GC. The bearings are actually part of the drum assembly. As such, there should be a dust cap over the outer bearing. Remove the dust cap, then the cotter pin, and pin back the hex nut. As you spin back the hex nut, you will unload the bearings, and you should notice the drum fall downward slightly. All you have to do is remove the nut completely and then the drum should slide off. The outer bearing was held in by the nut and a washer. The inner bearing was held in place by a bearing retaining seal. I had to do this because I needed to re-pack my rear wheel bearings. But I did take the opportunity to clean, inspect and adjust my rear brakes at the same time. hth On Thu, 21 Sep 2006 15:43:27 -0500, Robbie and Laura Reynolds > wrote: >I am planning to inspect my rear brakes this weekend, as I suspect there >might be a problem back there. I tried briefly to get one rear drum off >a few months ago when I replaced the front brakes, but it was being held >in place somehow and I didn't feel like messing with it at the time. >Before I get into it this Saturday, do you suppose it's just the shoes >getting caught on a ridge in the drum, or is there some kind of sneaky >pin or clip that holds this drum in place? |
#4
|
|||
|
|||
rear wheel drum on 1999 voyager
The 1999 model has a separate drum that goes on over the hub assembly.
I've had the older style drums off lots of times, but I've never had to do anything to this one yet. And the parking brake was off. NewMan wrote: > > I don't suppose you had the parking brake on by any chance??? > > If I recall correctly on my 1994 with rear drums, the style is > different than others I encountered. That is, on some vehicles I have > owned, the drum was NOT a part of the bearing assembly, so when the > wheel was removed, you could simply slide the drum off to gain access > to the brake mechanism. > > This was NOT the case on my GC. The bearings are actually part of the > drum assembly. As such, there should be a dust cap over the outer > bearing. Remove the dust cap, then the cotter pin, and pin back the > hex nut. As you spin back the hex nut, you will unload the bearings, > and you should notice the drum fall downward slightly. > > All you have to do is remove the nut completely and then the drum > should slide off. The outer bearing was held in by the nut and a > washer. The inner bearing was held in place by a bearing retaining > seal. > > I had to do this because I needed to re-pack my rear wheel bearings. > But I did take the opportunity to clean, inspect and adjust my rear > brakes at the same time. > > hth > > On Thu, 21 Sep 2006 15:43:27 -0500, Robbie and Laura Reynolds > > wrote: > > >I am planning to inspect my rear brakes this weekend, as I suspect there > >might be a problem back there. I tried briefly to get one rear drum off > >a few months ago when I replaced the front brakes, but it was being held > >in place somehow and I didn't feel like messing with it at the time. > >Before I get into it this Saturday, do you suppose it's just the shoes > >getting caught on a ridge in the drum, or is there some kind of sneaky > >pin or clip that holds this drum in place? |
#5
|
|||
|
|||
rear wheel drum on 1999 voyager
Robbie and Laura Reynolds Wrote: > I am planning to inspect my rear brakes this weekend, as I suspect > there > might be a problem back there. I tried briefly to get one rear drum > off > a few months ago when I replaced the front brakes, but it was being > held > in place somehow and I didn't feel like messing with it at the time. > Before I get into it this Saturday, do you suppose it's just the shoes > getting caught on a ridge in the drum, or is there some kind of sneaky > pin or clip that holds this drum in place? Drum brakes have self adjusters. If it will not come off you will need to back off self adjuster. You will need a wire or curver object to reach in there and push the adjuster lever back so you can spin the adjuster wheel back to losen it up. Takes a little practice and a repair manual may help. Good luck. MT -- MT-2500 ------------------------------------------------------------------------ MT-2500's Profile: http://www.automotiveforums.com/vbul...?userid=382930 View this thread: http://www.automotiveforums.com/vbul...d.php?t=622212 http://www.automotiveforums.com |
#6
|
|||
|
|||
rear wheel drum on 1999 voyager
On Thu, 21 Sep 2006 15:43:27 -0500, Robbie and Laura Reynolds
> wrote: >I am planning to inspect my rear brakes this weekend, as I suspect there >might be a problem back there. I tried briefly to get one rear drum off >a few months ago when I replaced the front brakes, but it was being held >in place somehow and I didn't feel like messing with it at the time. >Before I get into it this Saturday, do you suppose it's just the shoes >getting caught on a ridge in the drum, or is there some kind of sneaky >pin or clip that holds this drum in place? <snip> This is FWD. Thus, I'd expect that you're probably trying to take the wheel bearing off without removing the nut. Take the hub cap off (no, not the wheel cover) and see if the the drum is riveted to the bearing hub. |
#7
|
|||
|
|||
rear wheel drum on 1999 voyager
:werd.. there should be an oval rubber plug on the backing plate, usually near the metal brake line going to the wheel cylinder... [image: http://www.autozone.com/images/cds/g...d801a4c1a.gif] see *#7* ? the thing right in the middle is the star-wheel adjuster... dunno which way you'll haveta go 50:50 in turning it up or down... *# 12* is what keeps the shoes adjusted properly to the drums & that's what's keeping your drum "stuck"... gotta lift this up & turn that wheel w/ another screwdriver in some cases... you'll see a ridge on the inner part of the drum when you finally remove it... adviseable to go have them resurfaced when removed... -edit: ha, ive found it!- all courtesy to autozone free online repair manual! [image: http://www.autozone.com/images/cds/j...d801a4c39.jpg] rubber plug [image: http://www.autozone.com/images/cds/j...d801a4b8b.jpg] using a special brake tool or flathead screwdriver & a few expletives should do it! Newman's case is different since he didn't have the sealed hub-bearing design... wright z28's testimony: yeap, my sis' 97 chevy cavalier didn't come w/ that rubber plug in the back & had to bring out a big rubber mallet, said a few expletives & bang it loose to take the drum off; what were u thinking GM?!?! -- ricebike ------------------------------------------------------------------------ ricebike's Profile: http://www.automotiveforums.com/vbul...?userid=361742 View this thread: http://www.automotiveforums.com/vbul...d.php?t=622212 http://www.automotiveforums.com |
#8
|
|||
|
|||
rear wheel drum on 1999 voyager
DeserTBoB wrote: > > On Thu, 21 Sep 2006 15:43:27 -0500, Robbie and Laura Reynolds > > wrote: > > >I am planning to inspect my rear brakes this weekend, as I suspect there > >might be a problem back there. I tried briefly to get one rear drum off > >a few months ago when I replaced the front brakes, but it was being held > >in place somehow and I didn't feel like messing with it at the time. > >Before I get into it this Saturday, do you suppose it's just the shoes > >getting caught on a ridge in the drum, or is there some kind of sneaky > >pin or clip that holds this drum in place? <snip> > > This is FWD. Thus, I'd expect that you're probably trying to take the > wheel bearing off without removing the nut. Take the hub cap off (no, > not the wheel cover) and see if the the drum is riveted to the bearing > hub. Per my other post, the drum comes off without removing the bearing assembly. Concensus seems to be that there is no hidden attachment hardware on this drum. Thanks so much. |
#9
|
|||
|
|||
rear wheel drum on 1999 voyager
My nephew was trying to get the drum off a Corolla and I told him to
loosen the adjuster nut. It didn't help, so as a last resort I asked him for an exact account of everything he had done to get ready for the job. His list included setting the parking brake. Oops. I'm sure this one will come right off as soon as I loosen the adjuster. I was just making sure that there wasn't some tricky clip or retaining pin in there somewhere. |
#10
|
|||
|
|||
rear wheel drum on 1999 voyager
Robbie and Laura Reynolds wrote:
> I am planning to inspect my rear brakes this weekend, as I suspect there > might be a problem back there. I tried briefly to get one rear drum off > a few months ago when I replaced the front brakes, but it was being held > in place somehow and I didn't feel like messing with it at the time. > Before I get into it this Saturday, do you suppose it's just the shoes > getting caught on a ridge in the drum, or is there some kind of sneaky > pin or clip that holds this drum in place? It's the shoes behind the wear ridge. Pull out the rubber plug and use a large screwdriver to back off the adjuster wheel. Matt |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
71 ghia rear wheel bearings: do they 'run in oil' or are they 'packedwith grease'? | dave | VW air cooled | 4 | March 8th 06 05:38 PM |
Ping Tigger: case study on rear O2 sensor and fuel trim | Stephen H | Honda | 0 | December 24th 05 05:37 AM |
New *FREE* Corvette Discussion Forum | JLA ENTERPRISES TECHNOLOGIES INTEGRATION | Corvette | 12 | November 30th 04 06:36 PM |
No rear A/C in 1999 Grand Caravan | Anon | Dodge | 4 | June 5th 04 02:16 PM |