If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#11
|
|||
|
|||
How do you "tune up" a hard-to-start Craftsman 18" chainsaw
On Sat, 21 Aug 2010 19:08:40 -0500, The Daring Dufas wrote:
> It's not rocket surgery. 8-) LOL! |
Ads |
#12
|
|||
|
|||
How do you "tune up" a hard-to-start Craftsman 18" chainsaw
On Sat, 21 Aug 2010 19:08:40 -0500, The Daring Dufas wrote:
> All reciprocating (piston) engines are basically air pumps. Ah. Now I understand what you're saying. Thanks for the details. I tried blowing about 50psi compressed air into the spark plug hole ... with mixed results (my compressor doesn't go higher than that). - If the piston was at the top, it fluttered (see details below). - If the piston was at another spot, it blew out the exhaust. - If the piston was at yet another spot, it blew out the carbeurator. But it never did run the thing (I think because of the pull-cord clutch mechanism because it 'looked' like it wanted to spin but couldn't spin. Probably because it wasn't fast enough to make the pull-cord clutch disengage. So, I think the "fluttering" was the piston trying to turn the crankshaft but it couldn't because of the pull cord. I guess I could remove the pull cord and test it without the pull-cord clutch... |
#13
|
|||
|
|||
How do you "tune up" a hard-to-start Craftsman 18" chainsaw
On Sun, 22 Aug 2010 01:29:48 GMT, notbob wrote:
> Size of the cylinder has no bearing on amount of pressure. That makes sense. I practically filled the thing with carb cleaner today. I'm letting it all dry out before I try again. If this last ditch effort doesn't work, plan B is to bring it to a shop for an estimate. Plan C, is to buy a NON-CALIFORNIA chain saw on the net. Can you recommend a good place to buy chain saws (NON CALIFORNIA EMISSIONS) that actually have adjustable "L" low and "H" high screws for the carb? |
#14
|
|||
|
|||
How do you "tune up" a hard-to-start Craftsman 18" chainsaw
On 8/22/2010 7:15 PM, SF Man wrote:
> On Sat, 21 Aug 2010 19:08:40 -0500, The Daring Dufas wrote: > >> All reciprocating (piston) engines are basically air pumps. > > Ah. Now I understand what you're saying. Thanks for the details. > > I tried blowing about 50psi compressed air into the spark plug hole ... > with mixed results (my compressor doesn't go higher than that). > > - If the piston was at the top, it fluttered (see details below). > - If the piston was at another spot, it blew out the exhaust. > - If the piston was at yet another spot, it blew out the carbeurator. > > But it never did run the thing (I think because of the pull-cord clutch > mechanism because it 'looked' like it wanted to spin but couldn't spin. > Probably because it wasn't fast enough to make the pull-cord clutch > disengage. > > So, I think the "fluttering" was the piston trying to turn the crankshaft > but it couldn't because of the pull cord. I guess I could remove the pull > cord and test it without the pull-cord clutch... If you'll look up how a two cycle engine works, you will understand why the air came out where it did. The position of the piston is what acts like the valves in a four cycle engine by uncovering the intake port or the exhaust port. If the reed valve is good, there shouldn't be any air coming out of the carburetor. Here's a link to an animation that shows how a two stroke engine works: http://science.howstuffworks.com/tra...wo-stroke2.htm http://preview.tinyurl.com/33qdr5p A bad reed valve could keep it from running on compressed air. TDD |
#15
|
|||
|
|||
How do you "tune up" a hard-to-start Craftsman 18" chainsaw
On 2010-08-23, SF Man > wrote:
> Plan C, is to buy a NON-CALIFORNIA chain saw on the net. Can you recommend > a good place to buy chain saws (NON CALIFORNIA EMISSIONS) that actually > have adjustable "L" low and "H" high screws for the carb? Sorry, but I've had little to no experience with chainsaws and 2-stroke yard tools, despite their being the same engines. In fact, I had a terrible time with the chainsaws and gas trimmers I inherited when my brother passed away. I couldn't get any of them to start, either, mainly cuz they were all junk, with cracked primer bulbs and hardened broken fuel lines and cracked plug wires. There's some real crappy merchandise being foisted off on the public, these days. nb |
#16
|
|||
|
|||
How do you "tune up" a hard-to-start Craftsman 18" chainsaw
On Sun, 22 Aug 2010 17:18:49 -0700, SF Man wrote:
> On Sun, 22 Aug 2010 01:29:48 GMT, notbob wrote: > >> Size of the cylinder has no bearing on amount of pressure. > > That makes sense. I practically filled the thing with carb cleaner > today. I'm letting it all dry out before I try again. > > If this last ditch effort doesn't work, plan B is to bring it to a shop > for an estimate. Check that the gasket between the carb and engine is good, that the carb is bolted on tightly, and that the crankcase cover[1] is bolted on tightly and with a good seal. On most of these engines the carb's fuel pump runs from crankcase pressure, so if there are any leaks in the system all sorts of strange things can happen - after ruling out spark and fuel line/filter, I'd try there next I think. Also pull the flywheel; it might be that the flywheel key has sheared and the timing's out a little - maybe not enough to stop it running (with a loss of power, but that might not be noticable), but enough to make it hard to start. [1] taking the cover off for a moment just to see if the bore is damaged might not be a bad idea, either. (re. compression, I posted here about a 4-stroke mower engine earlier in the year; that one turned out to be compression loss due to bore damage, even though it felt like it had "enough" compression when I stuck my thumb over the spark plug hole) cheers Jules |
#17
|
|||
|
|||
How do you "tune up" a hard-to-start Craftsman 18" chainsaw
"SF Man" > wrote in message ... > On Sun, 22 Aug 2010 01:29:48 GMT, notbob wrote: > >> Size of the cylinder has no bearing on amount of pressure. > > That makes sense. I practically filled the thing with carb cleaner today. > I'm letting it all dry out before I try again. > > If this last ditch effort doesn't work, plan B is to bring it to a shop > for > an estimate. > > Plan C, is to buy a NON-CALIFORNIA chain saw on the net. Can you recommend > a good place to buy chain saws (NON CALIFORNIA EMISSIONS) that actually > have adjustable "L" low and "H" high screws for the carb? I would recommend you go straight to "B". An honest saw mechanic can either fix this rascal quickly, or he can tell you it isnt worth fixing. I never bought a saw on the net. My first chain saw was an Echo, and it was a heck of a good saw. Then I bought a Husqvarna (also a great saw, stolen by a couple of drugheads), and then a replacement Husqvarna. I dont know if an internet company CAN ship a noncomplying saw to California. Note that some saws have what they used to call 50 hour engines. That is about the life expectancy of them. |
#18
|
|||
|
|||
How do you "tune up" a hard-to-start Craftsman 18" chainsaw
On Mon, 23 Aug 2010 09:51:13 -0500, hls wrote:
> Note that some saws have what they used to call 50 hour engines. That > is about the life expectancy of them. Or you get a "Friday engine", assembled by someone who is itching to get away for the weekend and so not paying as much attention to their work as they should :-( |
#19
|
|||
|
|||
How do you "tune up" a hard-to-start Craftsman 18" chainsaw
On Sun, 22 Aug 2010 20:30:10 -0500, The Daring Dufas wrote:
This is the California Poulan owners manual for my Craftsman chain saw. http://www.billious.com/ipls/pwe/pp3...2005-06-03.pdf Unfortunately you can't adjust anything when/if the carb gets clogged. It's California's way of stimulating the economy while saving the environment. It either works or you throw it away and buy a new one every two years. |
#20
|
|||
|
|||
How do you "tune up" a hard-to-start Craftsman 18" chainsaw
Stihl chainsaws are top rated chainsaws.
Last year, a guy who lives across the street from me borrowed my old Remington electric chain saw.He told me he is an old country boy and he knows all about chainsaws.HA!, he couldn't even figure out how to turn it on, I showed him half a dozen times and also how to keep the chain adjusted properly.About half an hour later, he brought it back over here.The chain was off the bar and all snaggled up and a little metal plate which keeps the chain from flying off of the clutch was broken.He broke my chainsaw. I have owned a few gas engine chainsaws before, but I never broke any of them. Last year, he couldn't figure out how to find the oil drain plug on the bottom of his lawn mower.He pushed his lawn mower over here, he said, Show me where that oil drain plug is! Only took me a few seconds to show him.He was to lazy to wipe his hand under there and look for that oil drain plug. cuhulin |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
How do you "tune up" a hard-to-start Craftsman 18" chainsaw | SF Man | Technology | 6 | August 21st 10 09:26 PM |
"Ford F-Series is hard to beat in the fight for supremacy" | Mike | Ford Explorer | 0 | April 1st 07 04:14 AM |
'98 Explorer "Tune up" advice | [email protected] | Ford Explorer | 2 | February 22nd 06 12:44 AM |