If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
petrol gauge not working
i have a 1997 e36 328,the prtrol gauge hes stopped working. Its showing
empty & the red light is on but has half a tank left. The range on the computer does not work either? any easy ideas to start with ? |
Ads |
#2
|
|||
|
|||
There are two fuel level sensors, one in the left lobe of the fuel tank and
another in the right lobe. They can be accessed by lifting the rear seat cushion out, and folding back the tar paper moisture barrier. The left side sensor is a sensor only, the right side sensor is part of the fuel pump assembly. In my car, it turned out that the left side sensor was dirty, and cleaning it resolved the problem. Odds are that whichever sensor you go after first, the other one is the problem. I think it was Murphy that said that whenever you have a 50/50 chance of picking the right option, the odds are 90 to 1 that you will pick the wrong option first. Anyway, the float has a wiper thingie on it, and the base has a contact strip. Using a business card (the course type), slip the card between the wiper and the strip, and GENTLY move it around until you no longer get black streaks on it. You can use Contact Cleaner as well, but you still need the card to scrape away the gunk and crud. DO NOT BEND THE WIPER THINGIE, or it will not make contact with the strip, and you will still have no fuel level indication. "bono" > wrote in message lkaboutautos.com... > i have a 1997 e36 328,the prtrol gauge hes stopped working. Its showing > empty & the red light is on but has half a tank left. The range on the > computer does not work either? any easy ideas to start with ? > |
#3
|
|||
|
|||
hi thanx for the advice. ive found the sensors under the back seat but dont
know how to take them out. alls ive done is to unscrew the sensor holder but i dont know wot to do next as i'm wary of pulling something which i dont know enough about. wots the next stage, step by step? |
#4
|
|||
|
|||
"bono" > wrote in message lkaboutautos.com... > hi thanx for the advice. ive found the sensors under the back seat but dont > know how to take them out. alls ive done is to unscrew the sensor holder > but i dont know wot to do next as i'm wary of pulling something which i > dont know enough about. wots the next stage, step by step? > That's a difficult question. Go to amazon.com and order yourself a Bently manual that covers your car. I have seen them listed on eBay. Back to the question at hand, BEFORE YOU START, YOU SHOULD BE SURE THE TANK IS NEARLY EMPTY. I reset my trip meter each time I fill the tank, and I know I can average 25mpg, and that I can carry 16 gallons. 25 x 16 = 400, so at about 350 miles into a tank of gas, I went to work on the sending units. You can do this job with a gallon or two in the tank, it would difficult with more than that. There is an obvious fire hazard working around the gas fumes, so take the necessary precautions of adequate ventilation, and smoking prohibitions. The sending units (I suggest starting with the left one first since the right one includes the fuel pump. Both come out the same way, but the one with the pump is incrementally more difficult to handle.) come out by unscrewing the ring. Of course, you have to disconnect the hoses and connectors first. To remove the ring, I used a long extension to my ratchet wrench and a small hammer to gently tap the vanes on the ring to knock it loose. Once it comes loose, it can easily spin by hand. Take the ring off and remove the sending unit. You have to move it around and squeeze it a little to fit it through the hole. There is an O-ring that you will want to be sure to not damage. Once the sending unit is out and on your work bench, it is easy to find the contacts, both the wiper part and the contact strip. I used a business card to clean the wiper contact that is part of the float arm itself, and a typewriter eraser (the pencil type that is very course and has the small brush on the end). You can use any suitable tool, perhaps a very fine emery cloth would do the trick. I also used Contact Cleaner as a solvent to carry the dirt away. I used my DVM to test the continuity of the sensor circuit, and when I had a reliable change in the DVM readings as I moved the float up and down, I knew the operation was a success. Before I started, I recall that I had flat resistance throughout all positions of the float arm; after cleaning the contact wiper and strip, the resistance changed through a relatively wide band. |
#5
|
|||
|
|||
hi,did wot you said & cleaned both senors but still no joy so it looks like
i'll need to take it in. Thanks for your advice & if you think of anything else could you let me know. cheers |
#6
|
|||
|
|||
You will need to use your ohm meter on the fuel level sending units to see
which one is open. "bono" > wrote in message lkaboutautos.com... > hi,did wot you said & cleaned both senors but still no joy so it looks > like > i'll need to take it in. Thanks for your advice & if you think of anything > else could you let me know. cheers > |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
E34 ('91 M5) gas gauge wonky | Doug Main | BMW | 0 | October 11th 04 05:57 PM |
Erratic Fuel Gauge | Graham Humphreys | Audi | 4 | July 6th 04 04:30 PM |
petrol prices | Tom | Alfa Romeo | 5 | June 2nd 04 09:45 PM |
Audi 100 quattro temp gauge probs | Paul Wickham | Audi | 1 | May 31st 04 04:39 PM |
temperature gauge problems Uk model 1992 K reg 100 2.3 quattro AAR | Paul Wickham | Audi | 0 | May 22nd 04 05:47 PM |