If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
License Plate Light Dead, Failed Inspection - Replaced Bulbs, Nothing - Now What?
Went to the freakin state inspection in NJ yesterday. This is on my 90
Golf. It fails on NOTHING except the freakin rear license plate light. For those that have had to endure a NJ auto inspection, you have not had the pleasure. Regardless, I replaced the bulbs, no joy. Nothing. Pulled the driver side panel in the trunk off. Found the wire for the lights measured it with a multimeter come from the front. So its putting out juice. So I figure its the blasted harness in the hatch. Most likely a wire is broken in the rubber boot going up into the hatch. Is there anyway I can test the wires up there without ripping off the insulation? Someone mentioned using a pin with the multimeter and sticking it into the wire. Anyone have any ideas? I really dont want to pull the whole dam harness out. Have to remove the speaker deck panel, the real seat belt, the wiper motor, etc.... Dont want to go there. |
Ads |
#2
|
|||
|
|||
John W. wrote:
> Went to the freakin state inspection in NJ yesterday. This is on my 90 > Golf. It fails on NOTHING except the freakin rear license plate light. > For those that have had to endure a NJ auto inspection, you have not > had the pleasure. > > Regardless, I replaced the bulbs, no joy. Nothing. Pulled the driver > side panel in the trunk off. Found the wire for the lights measured it > with a multimeter come from the front. So its putting out juice. So I > figure its the blasted harness in the hatch. Most likely a wire is > broken in the rubber boot going up into the hatch. > > Is there anyway I can test the wires up there without ripping off the > insulation? Someone mentioned using a pin with the multimeter and > sticking it into the wire. > > Anyone have any ideas? > > I really dont want to pull the whole dam harness out. Have to remove > the speaker deck panel, the real seat belt, the wiper motor, etc.... > > Dont want to go there. Well you could try moving the wires around to see if there could be an intermittent failure. Most likely place for that is where it bends each time to boot is opened. However I am going to suggest you take a look at the other side. Check the ground. -- Joseph Meehan Dia duit |
#3
|
|||
|
|||
> However I am going to suggest you take a look at the other side.
Check > the ground. What he said. Make sure you've not only got positive to the light but that the ground is reliable. |
#4
|
|||
|
|||
In rec.autos.makers.vw.watercooled, John W. wrote:
> >Is there anyway I can test the wires up there without ripping off the >insulation? Someone mentioned using a pin with the multimeter and >sticking it into the wire. The pin works, but a small needle is better. Get a small one. Sharper and stronger than a pin. |
#5
|
|||
|
|||
In rec.autos.makers.vw.watercooled, Tom's VR6 wrote:
>In rec.autos.makers.vw.watercooled, John W. wrote: > >> >>Is there anyway I can test the wires up there without ripping off the >>insulation? Someone mentioned using a pin with the multimeter and >>sticking it into the wire. > >The pin works, but a small needle is better. Get a small one. >Sharper and stronger than a pin. And the suggestion about checking the ground is a good one. With the meter, check that you don't have voltage between the outer part of the socket and a chassis ground. |
#6
|
|||
|
|||
In rec.autos.makers.vw.watercooled, Tom's VR6 wrote:
> >And the suggestion about checking the ground is a good one. With the >meter, check that you don't have voltage between the outer part of >the socket and a chassis ground. .... with a bulb in that socket and the lights on. |
#7
|
|||
|
|||
I recently had to replace all 4 side marker lightbulb sockets in my 1988
Cabbie. They just refused to make good electrical contact. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
E34: License Light works but error message displayed | Chip L | BMW | 6 | January 17th 05 05:44 PM |
Went for inspection, failed because "Catalytic converter not READY" code is coming | Santa | Honda | 12 | November 20th 04 07:22 PM |
88 535i inspection light | David N Emmet | BMW | 3 | November 19th 04 08:44 PM |
When The Battery Light Comes On Does This Mean The Battery Is Going Dead? | John | Saturn | 10 | August 14th 04 01:25 AM |