If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
Rear suspension is off!
http://www.tegger.com/hondafaq/misc/...suspension.jpg
I'm off to the machine shop tomorrow to get the bushings pressed out. This has easily been the most frightening job I've ever attempted, mostly due to the amount of disassembly required. Ain't nothin' left of that back end. -- TeGGeR® The Unofficial Honda/Acura FAQ www.tegger.com/hondafaq/ |
#2
|
|||
|
|||
On 23 Jul 2005 01:37:27 GMT, "TeGGeR®" > wrote:
>http://www.tegger.com/hondafaq/misc/...suspension.jpg > >I'm off to the machine shop tomorrow to get the bushings pressed out. > >This has easily been the most frightening job I've ever attempted, mostly >due to the amount of disassembly required. Ain't nothin' left of that back >end. beat them out with a hammer, we don't press them at the shop. I've done them on the car. Chip |
#3
|
|||
|
|||
chip > wrote in
: > On 23 Jul 2005 01:37:27 GMT, "TeGGeR®" > wrote: > >>http://www.tegger.com/hondafaq/misc/...suspension.jpg >> >>I'm off to the machine shop tomorrow to get the bushings pressed out. >> >>This has easily been the most frightening job I've ever attempted, >>mostly due to the amount of disassembly required. Ain't nothin' left >>of that back end. > > > > beat them out with a hammer, we don't press them at the shop. I've > done them on the car. > Chip Even the shop had some trouble due to the rust. I would have been stuck had I tried that method. Also, four bolts took a big air wrench to get loose, and one never did come out and needed to be ground off. Unfortunately, the shop also managed to knock off the nut (on the trailing arm) for the bolt on the outer end of the lower control arm. Now I have to get a new Grade-10 bolt and nut to fit that area. I've temporarily got a 10x70mm Grade-8 bolt and Nyloc nut from Home Depot in there just so I can button everything back up. And one of the bolts for the upper arm on the one side feels like it wants to cross-thread, and of course the stores are now closed and I don't have the correct size tap to chase the threads with. -- TeGGeR® The Unofficial Honda/Acura FAQ www.tegger.com/hondafaq/ |
#4
|
|||
|
|||
TeGGeR® wrote:
> chip > wrote in > : > > >>On 23 Jul 2005 01:37:27 GMT, "TeGGeR®" > wrote: >> >> >>>http://www.tegger.com/hondafaq/misc/...suspension.jpg >>> >>>I'm off to the machine shop tomorrow to get the bushings pressed out. >>> >>>This has easily been the most frightening job I've ever attempted, >>>mostly due to the amount of disassembly required. Ain't nothin' left >>>of that back end. >> >> >> >>beat them out with a hammer, we don't press them at the shop. I've >>done them on the car. >> Chip > > > > > Even the shop had some trouble due to the rust. I would have been stuck had > I tried that method. > > Also, four bolts took a big air wrench to get loose, and one never did come > out and needed to be ground off. Unfortunately, the shop also managed to > knock off the nut (on the trailing arm) for the bolt on the outer end of > the lower control arm. Now I have to get a new Grade-10 bolt and nut to fit > that area. I've temporarily got a 10x70mm Grade-8 bolt and Nyloc nut from > Home Depot in there just so I can button everything back up. > > And one of the bolts for the upper arm on the one side feels like it wants > to cross-thread, and of course the stores are now closed and I don't have > the correct size tap to chase the threads with. > try not to chase if you can avoid it. if you jack the arm up into position and use the right bolt, the one with the rounded end, you should be able to get it in ok. the jacking bit is the key. one time, i even dropped the two big pivot bolts back off to make it easier to get a difficult top arm in. once located & loosely bolted, getting the pivot bolts back was fairly straight forward. do the one with the elongated slot first. |
#5
|
|||
|
|||
jim beam > wrote in
: >> > try not to chase if you can avoid it. if you jack the arm up into > position and use the right bolt, the one with the rounded end, you > should be able to get it in ok. the jacking bit is the key. one > time, i even dropped the two big pivot bolts back off to make it > easier to get a difficult top arm in. once located & loosely bolted, > getting the pivot bolts back was fairly straight forward. do the one > with the elongated slot first. > > That's not the problem. I have a clear view into the hole (left side, rear slotted hole) and it's a totally clear path into the hole. I can get it to take the first two threads or so, but then it binds, like it does when it seats. Or cross-threads. The other bolt is fully home. Just settled the suspension. Ride height is back where it should be. I'm off to tighten and align. -- TeGGeR® The Unofficial Honda/Acura FAQ www.tegger.com/hondafaq/ |
#6
|
|||
|
|||
jim beam > wrote in
: >> > try not to chase if you can avoid it. if you jack the arm up into > position and use the right bolt, the one with the rounded end, you > should be able to get it in ok. the jacking bit is the key. one > time, i even dropped the two big pivot bolts back off to make it > easier to get a difficult top arm in. once located & loosely bolted, > getting the pivot bolts back was fairly straight forward. do the one > with the elongated slot first. > By the way, I tried a bolt from the other side and the same thing happened, so I'm sure there's a burr in there somewhere. -- TeGGeR® The Unofficial Honda/Acura FAQ www.tegger.com/hondafaq/ |
#7
|
|||
|
|||
Weird...
No matter where I lever the trailing arm before tightening the compensator arm, the toe does not change. It's exactly the same as what I measured before I took everything apart. That position is what they return to naturally when I drive onto the newspaper. (I put a thin section of newspaper under the tires so they could pivot more easily.) -- TeGGeR® The Unofficial Honda/Acura FAQ www.tegger.com/hondafaq/ |
#8
|
|||
|
|||
TeGGeR® wrote:
> Weird... > > No matter where I lever the trailing arm before tightening the compensator > arm, the toe does not change. It's exactly the same as what I measured > before I took everything apart. > > That position is what they return to naturally when I drive onto the > newspaper. (I put a thin section of newspaper under the tires so they could > pivot more easily.) > it does change. if you watch the tech in the alignment shop, the gauges show it changing as they make their adjustments. but they're real small, and as you'll find out driving to & from the alignment shop, they make an interesting difference. |
#9
|
|||
|
|||
TeGGeR® wrote:
> http://www.tegger.com/hondafaq/misc/...suspension.jpg > > I'm off to the machine shop tomorrow to get the bushings pressed out. > > This has easily been the most frightening job I've ever attempted, mostly > due to the amount of disassembly required. Ain't nothin' left of that back > end. well, you're committed now! seriously, it's a very worthwhile job. you going to post pics of the old bushings? |
#10
|
|||
|
|||
jim beam > wrote in
: > TeGGeR® wrote: >> http://www.tegger.com/hondafaq/misc/...suspension.jpg >> >> I'm off to the machine shop tomorrow to get the bushings pressed out. >> >> This has easily been the most frightening job I've ever attempted, >> mostly due to the amount of disassembly required. Ain't nothin' left >> of that back end. > > well, you're committed now! seriously, it's a very worthwhile job. > you going to post pics of the old bushings? > It's all back in now, with a couple of headaches (see my reply to chip). Just have to put the brakes back together and do the roll-around bit before I set the alignment back to what I measured before I started, and tighten everythibg back up. I notice almost all the bolts have those little blue Nylon inserts in them. Now I'm wondering if I should get all new bolts or just use Loctite. The Red Loctite says it needs 450F of heat to be able to remove them once they've set, which makes me kinda leery of using it. And yes, I saved the old bushings. They look pretty gross. Both the big ones were almost severed on the top rubber leg. -- TeGGeR® The Unofficial Honda/Acura FAQ www.tegger.com/hondafaq/ |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
leaf springs | [email protected] | Corvette | 3 | March 10th 05 10:42 PM |
'88 Wagoneer rear suspension | mike92105 | Jeep | 8 | December 4th 04 06:41 PM |
New *FREE* Corvette Discussion Forum | JLA ENTERPRISES TECHNOLOGIES INTEGRATION | Corvette | 12 | November 30th 04 06:36 PM |
Manual rear air suspension | Mark Carroll | General | 1 | March 17th 04 03:14 PM |