![]() |
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
![]()
Croosh wrote:
Does anyone have tried that, or does anybody know waht grease is safe for the tank? There's a white grease that's used to lubricate plumbing fixtures. It's sold in plastic tins about 2" in diameter and 1/2" thick. It's safe enough to use on things people drink from. Lowes sells it, if there's one in your area. The stuff I use is "Plumber's Silicone Grease." It's made by Radiator Specialty Co., Charlotte, NC. George Patterson Coffee is only a way of stealing time that should by rights belong to your slightly older self. |
#2
|
|||
|
|||
![]()
George Patterson wrote:
Croosh wrote: Does anyone have tried that, or does anybody know waht grease is safe for the tank? There's a white grease that's used to lubricate plumbing fixtures. It's sold in plastic tins about 2" in diameter and 1/2" thick. It's safe enough to use on things people drink from. Lowes sells it, if there's one in your area. The stuff I use is "Plumber's Silicone Grease." It's made by Radiator Specialty Co., Charlotte, NC. Any decent hardware store will stock it, probably along with faucet, spigot and mixer valve repair kits. What do you want to grease in your tank? -K |
#3
|
|||
|
|||
![]()
Kelsey,
I bought two used sea swirls, but they are pretty beat up. I had to order a motor and the shaft needs to be lubricated. Thank you Yuriy |
#4
|
|||
|
|||
![]()
"Kelsey Cummings" wrote in message ...
What do you want to grease in your tank? Probably some rubber/silicone gaskets in his water pumps. |
#5
|
|||
|
|||
![]()
My instruction sheet on my CSS skimmers says to simnply use a light
coat of petrolatum (Vasel;ine) to coat Oring, and my papers on my other pump (Sequence) says the same thing to use a light coat of petrolatum to coat all orings such as is found on strainer baskets...... I have a large tube of Krytox grease.......but finding it locally may be a bit hard not to say EXPENSIVE..........I got mine at a DROM sale dirt cheap, as it was past its shelf life. Now that may make a difference for what that grease is intended for, but for a louosy fish tank and associated equipment its certaily better than anything your gonna find locally or even order on line to buy and use. Its main use is in liquid oxygen systems, under high pressure............I feel confortable with using it.....as its been just fine for a long while now............. On Tue, 18 Apr 2006 18:17:22 -0500, "Pszemol" wrote: "Kelsey Cummings" wrote in message ... What do you want to grease in your tank? Probably some rubber/silicone gaskets in his water pumps. -- \\\|/// ( @ @ ) -----------oOOo(_)oOOo--------------- oooO ---------( )----Oooo---------------- \ ( ( ) \_) ) / (_/ The original frugal ponder ! Koi-ahoi mates.... |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
New idea....scrapping epoxy and silicone idea | Squeek | General | 12 | March 10th 05 04:47 AM |
silicone sealant safe? | tim daley | General | 3 | July 22nd 04 05:16 PM |
removing silicone? | sophie | General | 6 | July 10th 04 05:27 PM |
silicone sand | Newsjes | General | 3 | December 29th 03 12:23 AM |
Which GE silicone? | dave | Cichlids | 8 | October 25th 03 10:07 PM |